Choose your language

Day Nursery "In der Mühle"

New kindergarten in Murg made of wood 

Die Kita besteht aus fünf in einander übergehende Einzelhäuser mit Satteldach, komplett aus Holz gebaut, zu großem Teil mit Elementen von Lignotrend,
Der für Eltern eingerichtet Warte-und Informationsbereich im Foyer, punktet mit edlen Farbakzenten in Blautönen und der eleganten Deckenverkleidung aus heller Weißtanne.
Im Foyer wurde ein Warte- und Infobereich für die Eltern eingerichtet. Der helle Raum öffnet sich in der Mitte schachtförmig bis ins Obergeschoss und wird so optisch vergrößert.
Die Brettsperrholz-Lösung mit Sichtseite aus hellem Akustikprofil schafft nicht nur eine einladende, warme Atmosphäre, sondern sorgt im Garderobenbereich auch dafür, dass störende Geräusche nicht die Überhand nehmen.
Im Obergeschoss, wie hier im großen Mehrzwecksaal mit einer Dachspannweite von rund 8 Metern sind die Schrägen der Satteldächer sichtbar. Die akustisch wirksamen Dachuntersichten absorbieren den Schall und sorgen dafür, dass aus lustigem Kinderspiel kein stressiger Lärm wird.
Wände und Decke komplett in Holz gekleidet und teilweise mit feinem Akustikprofil ausgestattet, entsteht zusammen mit dem glatten Boden in kräftigem Blau eine dynamisch, kreative Atmosphäre, in der die Kinder sich wohl fühlen.
Der in weiß und indigo blau gestaltete Speisesaal der Kita öffnet sich durch eine bodentiefe Fensterfront zur Natur. Die fein profilierte Deckenverkleidung aus Weißtanne made of LIGNO®, bringt ein weiteres Stück Natur ins Innere.
Die Reihen aus weißen und darüber blauen Schließfächern bilden ein dynamisches Farb-und Formkonzept mit der Decke aus feinen LIGNO® Akustikleisten und dem Boden in dunklerem Blau.
Eine quadratische schachtartige Öffnung erweitert das Foyer optisch nach oben und schafft eine Verbindung zwischen Unter-und Obergeschoss, mit seitlich integrierten Fenstern die den Blick von oben nach unten gewähren.
Die Kita in der Mühle in Murg ist ein naturgesunder Holzbau aus Brettsperrholz-Rippenelementen für Wand, Decke und Dach von Lignotrend. Architekt Ernesto Preiser löste das umfangreiche Raumprogramm kindgerecht auf und brachte es in fünf locker aneinandergereihten „Einzelhäuschen“ unter.

The new day nursery "In der Mühle" was built in one and a half years in the centre of Murg. The day care centre and regular kindergarten have space for a total of 100 children and have been in operation since the beginning of September 2020. At the ground-breaking ceremony in January 2019, Mayor Adrian Schmidle had already described the new day care centre "In der Mühle" as a milestone and an important puzzle for strengthening the centre of Murg.  

Configuration overview

Components used

  • LIGNO® Rippe Q3  |  Ceiling component

    Product code: LIGNO® Rippe Q3_230-290_r25_ssp_z26_p0_a50g_625-20-4_WTE_gb_buv
    Installation top


    Whether the element is open or closed at the top is determined by the area of application. If, for example, the element is to be filled with fill on site as a storey ceiling or roof terrace (LIGNO® Rippe Q3-x), its cavities are open at the top (feature _r0). To guide pipes at the top of the element, a cross grid (_r25, _r50) can be added to some superstructures. For roof superstructures, there is usually a flat closed finish _rg0 (LIGNO® Block Q-x, LIGNO® Block Q3-x or corresponding versions of LIGNO® Acoustic classic).

    Installation top

    _r25 25 mm Cross grid 

    Statics


    The height of the load-bearing webs of the element is variable and determined according to static requirements from load and span. Within the framework of this configurator, the selection is limited to four height ranges. A more precise definition is made later during pre-dimensioning or verification with the LTB-x calculation programme. Bulk volume and/or necessary space for installations can also be decisive for the height.

    Statics

    _230-290 Medium span

    Fire resistance


    If fire protection is required, an additional layer is added below the web area (for elements with strip profiles _z26, _z53, _z80, for elements with board profiles Akustik klassik _k50g). Their height determines the fire resistance duration of the cross-section from 30 to 90 minutes. The fire resistance must be statically verified. If there are no requirements, the standard versions _z0 or _k50l are to be selected.

    Fire resistance

    _z26 REI 30 Fire resistance 

    Cavity


    Panel designs with slat profiles and additional layer can be configured with an additional cavity (_p26, _p53) below the additional layer for installation guides, fixtures or to improve sound absorption. Cables laid there then do not penetrate the fire-protection layer. If required, the cavity is filled with insulating material (_p26mw, _p26ha) to improve acoustic absorption. If no cavity is necessary, the characteristic _p0 is selected. 

    Cavity

    _p0 No cavity

    Room acoustics


    If the soffit of the element is to have a good sound-absorbing effect, the penultimate layer is configured as absorber _a50g. Otherwise, this layer is configured as a solid wood layer _a0.

    Room acoustics

    _a50g Integrated absorber

    Profile


    The visible layer is profiled with joints. The code for profiling indicates in millimetres: Element width, strip width (rounded, from/to if applicable) and joint width (rounded) as well as a letter identification for variants, e.g. with chamfered strip edges or with additional height gradation. 

    Note: Some profiles indirectly cause exclusions for other configuration options.

    Profile 

    _625-20-4 Slat profile 

    Wood type


    Various wood species are available for the visible layer. For quality reasons, individual wood species cannot be configured for all profiles; for technical reasons, surface treatments are excluded for some wood species.

    Wood type

    _WTE Silver fir, economy 

    Structure


    The face is subjected to a brushing _gb as standard, which produces a stronger or weaker structure depending on the type of wood and makes the surface less sensitive to scratches.  Alternatively, a smooth sanding _gs can be carried out, or on request a bandsaw cut _grimitated.

    Structure

    _gb Brushed

    Treatment


    Depending on the type of wood, the optional application of a surface treatment is possible ex works. Individual colour finishes are always sampled for coordination. For elements in individual lengths, colour treatment is limited to max. 5 m length.

    Treatment

    _buv UV-protection stain

  • LIGNO® Block Q3  |  Roof component

    Product code: LIGNO® Block Q3_150-210_rg0_s0_z26_p0_a50g_625-20-4_WTE_gb_buv
    Installation top


    Whether the element is open or closed at the top is determined by the area of application. If, for example, the element is to be filled with fill on site as a storey ceiling or roof terrace (LIGNO® Rippe Q3-x), its cavities are open at the top (feature _r0). To guide pipes at the top of the element, a cross grid (_r25, _r50) can be added to some superstructures. For roof superstructures, there is usually a flat closed finish _rg0 (LIGNO® Block Q-x, LIGNO® Block Q3-x or corresponding versions of LIGNO® Acoustic classic).

    Installation top

    _rg0 Closed, without cross grid

    Statics


    The height of the load-bearing webs of the element is variable and determined according to static requirements from load and span. Within the framework of this configurator, the selection is limited to four height ranges. A more precise definition is made later during pre-dimensioning or verification with the LTB-x calculation programme. Bulk volume and/or necessary space for installations can also be decisive for the height.

    Statics

    _150-210 Small span  

    Fire resistance


    If fire protection is required, an additional layer is added below the web area (for elements with strip profiles _z26, _z53, _z80, for elements with board profiles Akustik klassik _k50g). Their height determines the fire resistance duration of the cross-section from 30 to 90 minutes. The fire resistance must be statically verified. If there are no requirements, the standard versions _z0 or _k50l are to be selected.

    Fire resistance

    _z26 REI 30 Fire resistance 

    Cavity


    Panel designs with slat profiles and additional layer can be configured with an additional cavity (_p26, _p53) below the additional layer for installation guides, fixtures or to improve sound absorption. Cables laid there then do not penetrate the fire-protection layer. If required, the cavity is filled with insulating material (_p26mw, _p26ha) to improve acoustic absorption. If no cavity is necessary, the characteristic _p0 is selected. 

    Cavity

    _p0 No cavity

    Room acoustics


    If the soffit of the element is to have a good sound-absorbing effect, the penultimate layer is configured as absorber _a50g. Otherwise, this layer is configured as a solid wood layer _a0.

    Room acoustics

    _a50g Integrated absorber 

    Profile


    The visible layer is profiled with joints. The code for profiling indicates in millimetres: Element width, strip width (rounded, from/to if applicable) and joint width (rounded) as well as a letter identification for variants, e.g. with chamfered strip edges or with additional height gradation. 

    Note: Some profiles indirectly cause exclusions for other configuration options.

    Profile 

    _625-20-4 Slat profile 

    Wood type


    Various wood species are available for the visible layer. For quality reasons, individual wood species cannot be configured for all profiles; for technical reasons, surface treatments are excluded for some wood species.

    Wood type

    _WTE Silver fir, economy 

    Structure


    The face is subjected to a brushing _gb as standard, which produces a stronger or weaker structure depending on the type of wood and makes the surface less sensitive to scratches.  Alternatively, a smooth sanding _gs can be carried out, or on request a bandsaw cut _grimitated.

    Structure

    _gb Brushed

    Treatment


    Depending on the type of wood, the optional application of a surface treatment is possible ex works. Individual colour finishes are always sampled for coordination. For elements in individual lengths, colour treatment is limited to max. 5 m length.

    Treatment

    _buv UV-protection stain 

  • LIGNO® Uni Q3 Visual quality  |  Wall component

    Product code: LIGNO® Uni Q3_123_625-621-4_WTE_gb_buv
    Statics


    The height of the load-bearing webs of the element is variable and determined according to static requirements from load and span. Within the framework of this configurator, the selection is limited to four height ranges. A more precise definition is made later during pre-dimensioning or verification with the LTB-x calculation programme. Bulk volume and/or necessary space for installations can also be decisive for the height.

    Element height

    _123 mm 

    Profile


    The visible layer is profiled with joints. The code for profiling indicates in millimetres: Element width, strip width (rounded, from/to if applicable) and joint width (rounded) as well as a letter identification for variants, e.g. with chamfered strip edges or with additional height gradation. 

    Note: Some profiles indirectly cause exclusions for other configuration options.

    Profile 

    _625-621-4 Closed surface

    Wood type


    Various wood species are available for the visible layer. For quality reasons, individual wood species cannot be configured for all profiles; for technical reasons, surface treatments are excluded for some wood species.

    Wood type

    _WTE Silver fir, economy 

    Structure


    The face is subjected to a brushing _gb as standard, which produces a stronger or weaker structure depending on the type of wood and makes the surface less sensitive to scratches.  Alternatively, a smooth sanding _gs can be carried out, or on request a bandsaw cut _grimitated.

    Structure

    _gb Brushed

    Treatment


    Depending on the type of wood, the optional application of a surface treatment is possible ex works. Individual colour finishes are always sampled for coordination. For elements in individual lengths, colour treatment is limited to max. 5 m length.

    Treatment

    _buv UV-protection stain

Reference-related

Downloads

Project participants

  • Architekturbüro Ernesto Preiser

    Architect

    Daimlerstraße 15
    79761 Waldshut-Tiengen
     

    www.architektpreiser.de

  • Zimmerei Kock & Götte

    Execution

    Rotlaubweg 21
    79809 Weilheim

    www.zimmerei-kock-goette.de

  • Foto & Design Gröber GmbH & Co.KG

    Photographer

    Untere Haspelstraße 29
    79761 Waldshut-Tiengen

     

    www.foto-und-design.com

  • Related references

      Largest school in France

      No one misses the new school complex at the centre of the revitalised Pasteur district of Limeil-Brévannes...

      94450 FR-Limeil-Brévannes 

      View
        titletitletitletitletitletitletitle

      Speech therapy school at the Kieferwäldchen

      The new speech therapy school in Griesheim, Hesse, is located in a wooded area with an old...

      64347 Griesheim 

      View
        titletitletitletitletitletitle